.
Posted: Sat Dec 20, 2008 11:35 pm
.
Pitty Mardave didn't print more accurate set up instructions.
Still seems slow though
Page 1 of 2
Re: Error in programming Mardave Brushless . . .THE FIX
Posted: Sun Dec 21, 2008 9:07 am
Well done Gazza.
Pitty Mardave didn't print more accurate set up instructions.
Still seems slow though
Pitty Mardave didn't print more accurate set up instructions.
Still seems slow though
Re: Error in programming Mardave Brushless . . .THE FIX
Posted: Sun Dec 21, 2008 9:44 am
Hi All
Good Note Gazza,
I have not tried setting mine up yet, but I was reading the instructions last night and they do refer to the setup procedure and in Red state that if you don't want to go into the calibration mode you should wait till the bleep, if you touch the throttle before the bleep it will enter calibration mode. To be truthful I was tipped off to read the instructions before installing, normally like everyone else I would have installed the unit and only read the instructions when it didn't work !
Good Note Gazza,
I have not tried setting mine up yet, but I was reading the instructions last night and they do refer to the setup procedure and in Red state that if you don't want to go into the calibration mode you should wait till the bleep, if you touch the throttle before the bleep it will enter calibration mode. To be truthful I was tipped off to read the instructions before installing, normally like everyone else I would have installed the unit and only read the instructions when it didn't work !
.
Posted: Sun Dec 21, 2008 1:35 pm
.
.
Posted: Mon Dec 22, 2008 1:16 pm
.
Re: UPDATE programming Mardave Brushless . . .THE FIX 22/12/08
Posted: Mon Dec 22, 2008 9:13 pm
Hi Gazza
I ve got the KO Vantage II and my throttle needs to be set to operate in reverse for it to work.
What also seems to work for me is:
Wait fo the 5 min delay or reprogram
wait for the first bleep followed by a green flashing light, then selected full forwards on the stick and release
wait for the red light (think flashing)then select and hold full reverse.
You then get the second bleep and bingo where do we race ?
I was getting a bit of a shunt start so I have set my starting speed to 34%, which seems to have settled it down quite nicely.
Richard
I ve got the KO Vantage II and my throttle needs to be set to operate in reverse for it to work.
What also seems to work for me is:
Wait fo the 5 min delay or reprogram
wait for the first bleep followed by a green flashing light, then selected full forwards on the stick and release
wait for the red light (think flashing)then select and hold full reverse.
You then get the second bleep and bingo where do we race ?
I was getting a bit of a shunt start so I have set my starting speed to 34%, which seems to have settled it down quite nicely.
Richard
Re: UPDATE programming Mardave Brushless . . .THE FIX 22/12/08
Posted: Mon Dec 22, 2008 9:49 pm
Anyone got any idea on gearing combinations, I would have though I would need to gear up slightly for a brushless.
Re: UPDATE programming Mardave Brushless . . .THE FIX 22/12/08
Posted: Mon Dec 22, 2008 10:19 pm
From chris the best way to gear them is to try the same gear ratio you had on your brushed
.
Posted: Tue Dec 23, 2008 1:07 am
.
Re: UPDATE programming Mardave Brushless . . .THE FIX 22/12/08
Posted: Tue Dec 23, 2008 1:12 am
Your asking a lot for a dry day aint you? mind you this saturday is there any raceing? as its non scoreing ?
.
Posted: Tue Dec 23, 2008 11:10 am
.
Re: UPDATE programming Mardave Brushless . . .THE FIX 22/12/08
Posted: Tue Dec 23, 2008 11:22 am
I might run the brushless system with you guy's as i need to work with it lol
.
Posted: Tue Dec 23, 2008 2:07 pm
.
Re: UPDATE programming Mardave Brushless . . .THE FIX 22/12/08
Posted: Tue Dec 23, 2008 4:16 pm
.
Re: UPDATE programming Mardave Brushless . . .THE FIX 22/12/08
Posted: Tue Dec 23, 2008 10:21 pm
http://www.mardaveracing.com/img/MOV03526.MPG
hope this link helps any body
hope this link helps any body