.

Post Reply
User avatar
Gazza
Forum Fisherman
Posts: 277
Joined: Sun May 25, 2008 6:21 pm
Name: GAZZA
Car: Mardave V12
Location: Leicester
Contact:

.

Post by Gazza »

.
Last edited by Gazza on Mon Nov 16, 2009 1:28 am, edited 1 time in total.
Richie
Senior Member
Senior Member
Posts: 156
Joined: Mon Feb 12, 2007 6:11 pm
Name: Richard Wilson
Location: Bedworth

Re: Mardave Brushless SETTINGS

Post by Richie »

Hi Gazza

Happy new year

Once again, Gazza to the rescue, good note, Thanks Gaz.

However I am still a little confused !

Your note appears to imply this is a battery problem/issue. Its your note "( taking into account you have good batterys and were fully charged)".

I wasn't of the opinion the dumping was caused by the batteries, or is this too simplistic a view ?
Logically this can be one of three things batteries, esc or motor. Assuming the batteries are OK, and the reference in your note applies to gearing then this has something to do with heat build up in either the esc or motor. Perhaps we can discuss on Saturday

Richard
User avatar
stox217
Expert Member
Expert Member
Posts: 342
Joined: Tue Nov 11, 2008 7:03 pm
Name: Nick
Car: V12
Location: Rugby

Re: Mardave Brushless SETTINGS

Post by stox217 »

try turning the brake force down to 40% and see how that go's
as i had no problems dumping with the systen i have
User avatar
Gazza
Forum Fisherman
Posts: 277
Joined: Sun May 25, 2008 6:21 pm
Name: GAZZA
Car: Mardave V12
Location: Leicester
Contact:

.

Post by Gazza »

.
Last edited by Gazza on Mon Nov 16, 2009 1:30 am, edited 1 time in total.
User avatar
Gazza
Forum Fisherman
Posts: 277
Joined: Sun May 25, 2008 6:21 pm
Name: GAZZA
Car: Mardave V12
Location: Leicester
Contact:

.

Post by Gazza »

.
Last edited by Gazza on Mon Nov 16, 2009 1:30 am, edited 1 time in total.
User avatar
stox217
Expert Member
Expert Member
Posts: 342
Joined: Tue Nov 11, 2008 7:03 pm
Name: Nick
Car: V12
Location: Rugby

Re: Mardave Brushless SETTINGS

Post by stox217 »

yep shure
running mode 2 (forward with reverse)
Drag brake force 8 (40% maximum drag brake fource)
Low voltage cut off 1 (off)
"drrs" start mode (punch) level 1 so very soft start
brake force 4 (100%)
Reverse force 2 (50%)
Initial brake fource 4 (40%)
Neutral range 2 (9%)
Timing 5 (15 degrees)
Motor type 1 (brushless motor)
Over heat protection 1 (enabled)
Hope this helps you lot
jayst
Senior Member
Senior Member
Posts: 142
Joined: Sat May 17, 2008 8:52 pm
Name: jamie cheshire
Car: T D . 210,410.408

Re: Mardave Brushless SETTINGS

Post by jayst »

i run them in my pan car lol
User avatar
Gazza
Forum Fisherman
Posts: 277
Joined: Sun May 25, 2008 6:21 pm
Name: GAZZA
Car: Mardave V12
Location: Leicester
Contact:

.

Post by Gazza »

.
Last edited by Gazza on Mon Nov 16, 2009 1:27 am, edited 1 time in total.
User avatar
stox217
Expert Member
Expert Member
Posts: 342
Joined: Tue Nov 11, 2008 7:03 pm
Name: Nick
Car: V12
Location: Rugby

Re: Mardave Brushless SETTINGS

Post by stox217 »

not its sensorless but i dont know about this timeing on the system i will have to figure out what it does
it might just be a power seting like 80% power or some thing like that
Post Reply